The short version of Stationary phase fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-06-30. Anything still debated is marked as such rather than presented as settled.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
While APHL primarily focuses on public health laboratories in the United States, their global health program makes an effort to help other countries strengthen their own laboratory practices.APHL works with more than 30 countries to: Share effective testing procedures Develop laboratory policies Improve the quality of data Train laboratory leaders Utilize information management systems Create strategies to monitor and detect Establish emergency response programs Design training programs APHL also works with public health laboratories around the world to share information on global health crises and promotes cross-border collaboration.
A typical intracellular concentration of ATP is 1–10 μmol per gram of muscle tissue in a variety of eukaryotes. The dephosphorylation of ATP and rephosphorylation of ADP and AMP occur repeatedly in the course of aerobic metabolism. ATP can be produced by a number of distinct cellular processes; the three main pathways in eukaryotes are (1) glycolysis, (2) the citric acid cycle/oxidative phosphorylation, and (3) beta-oxidation. The overall process of oxidizing glucose to carbon dioxide, the combination of pathways 1 and 2, known as cellular respiration, produces about 30 equivalents of ATP from each molecule of glucose. ATP production by a non-photosynthetic aerobic eukaryote occurs mainly in the mitochondria, which comprise nearly 25% of the volume of a typical cell.
The fas receptor (First apoptosis signal) – (also known as Apo-1 or CD95) is a transmembrane protein of the TNF family which binds the Fas ligand (FasL). The interaction between Fas and FasL results in the formation of the death-inducing signaling complex (DISC), which contains the FADD, caspase-8 and caspase-10. In some types of cells (type I), processed caspase-8 directly activates other members of the caspase family, and triggers the execution of apoptosis of the cell. In other types of cells (type II), the Fas-DISC starts a feedback loop that spirals into increasing release of proapoptotic factors from mitochondria and the amplified activation of caspase-8.
As a practical matter, when platinum group metals are purified through dissolution in aqua regia, gold (commonly associated with PGMs) is precipitated by treatment with iron(II) chloride. Platinum in the filtrate, as hexachloroplatinate(IV), is converted to ammonium hexachloroplatinate by the addition of ammonium chloride. This ammonium salt is extremely insoluble, and it can be filtered off. Ignition (strong heating) converts it to platinum metal: 3 [NH4]2[PtCl6] → 3 Pt + 2 N2 + 2 [NH4]Cl + 16 HCl Unprecipitated hexachloroplatinate(IV) is reduced with elemental zinc, and a similar method is suitable for small scale recovery of platinum from laboratory residues. Aqua regia reacts with tin to form tin(IV) chloride, containing tin in its highest oxidation state: 4 HCl + 2 HNO3 + Sn → SnCl4 + NO2 + NO + 3 H2O Aqua regia can react with iron pyrite to form iron(III) chloride: FeS2 + 5 HNO3 + 3 HCl → FeCl3 + 2 H2SO4 + 5 NO + 2 H2O
Sampling provides one rational means of verification that a production lot conforms to the requirements of technical specifications. 100% inspection does not guarantee 100% compliance and is too time-consuming and costly. Rather than evaluating all items, a specified sample is taken, inspected or tested, and a decision is made about accepting or rejecting the entire production lot. Sampling plans have known risks: an acceptable quality limit (AQL) and a rejectable quality level, such as lot tolerance percent defective (LTDP), are part of the operating characteristic curve of the sampling plan. These are primarily statistical risks and do not necessarily imply that a defective product is intentionally being made or accepted. Plans can have a known average outgoing quality limit (AOQL). A single sampling plan for attributes is a statistical method by which the lot is accepted or rejected on the basis of one sample. Suppose that we have a lot of sizes M {\displaystyle M} ; a random sample of size N < M {\displaystyle N<M} is selected from the lot; and an acceptance number B
Sources: en.wikipedia.org
Anoop's father, who was the Minister for Food and Civil Supplies, died on 30 October 2011. Following this, Anoop was nominated by the Kerala Congress (Jacob) and UDF to contest from the Piravom assembly seat previously represented by his father. His father had lost the sitting seat in 2006 elections and recaptured it in 2011 election by a margin of 157 votes. Against Anoop Jacob, CPI(M)–led LDF once again fielded M. J. Jacob, who had won against T. M. Jacob in 2006 and lost in 2011. Since the result of Piravom by-election mattered heavily to the ruling UDF who had a slender margin of 1 seat in the Legislative assembly over LDF, the constituency witnessed intense campaigning from both sides. Election was held on 17 March 2012 and results were announced on 21 March 2012. Anoop Jacob won the by-election by a significant margin of 12,071 votes. He was sworn in as an MLA on 22 March 2012. Anoop took oath as the Minister for Food & Civil Supplies on 12 April 2012 and occupied office in the North Block of the Kerala Secretariat; both portfolio & office last held by his departed father.
The primary medical treatment of acromegaly is to use somatostatin analogues – octreotide (Sandostatin) or lanreotide (Somatuline). Somatostatin analogues are also sometimes used to shrink large tumors before surgery. Because octreotide inhibits gastrointestinal and pancreatic function, long-term use causes digestive problems such as loose stools, nausea, and gas in one-third of people. In addition, approximately 25 percent of people with acromegaly develop gallstones, which are usually asymptomatic. In some cases, octreotide treatment can cause diabetes because somatostatin and its analogues can inhibit the release of insulin. With an aggressive adenoma that is not able to be operated on, there may be a resistance to octreotide in which case a second-generation SSA, pasireotide, may be used for tumor control. However, insulin and glucose levels should be carefully monitored as pasireotide has been associated with hyperglycemia by reducing insulin secretion.
The transduction of the signal through the membrane by the receptor is not completely understood. It is known that in the inactive state, the GPCR is bound to a heterotrimeric G protein complex. Binding of an agonist to the GPCR results in a conformational change in the receptor that is transmitted to the bound Gα subunit of the heterotrimeric G protein via protein domain dynamics. The activated Gα subunit exchanges GTP in place of GDP which in turn triggers the dissociation of Gα subunit from the Gβγ dimer and from the receptor. The dissociated Gα and Gβγ subunits interact with other intracellular proteins to continue the signal transduction cascade while the freed GPCR is able to rebind to another heterotrimeric G protein to form a new complex that is ready to initiate another round of signal transduction. It is believed that a receptor molecule exists in a conformational equilibrium between active and inactive biophysical states. The binding of ligands to the receptor may shift the equilibrium toward the active receptor states. Three types of ligands exist: Agonists are ligands that shift the equilibrium in favour of active states; inverse agonists are ligands that shift the equilibrium in favour of inactive states; and neutral antagonists are ligands that do not affect the equilibrium. It is not yet known how exactly the active and inactive states differ from each other.
BIA Separations was formed in 1998 by a group of scientists in Ljubljana, Slovenia to commercialize a new chromatographic resin based on monolith technology. Monolithic resin was developed independently by three different laboratories in late 1980s led by Hjertén, Švec and Tennikova. The company was one of the few Slovenian companies to receive venture capital funding at that time-Horizonte Venture Management realizing the potential of monoliths made the initial investment in the company. During that year, BIA Separations released its first commercial product marketed under the trade name of CIM (Convective Interaction Media). The new technique was named HPMC (High Performance Monolith Chromatography). During the 1999 and 2000s, the company promoted this new platform technology to the scientific and business community and registered several patents. In 2007 the company headquarters moved to Villach, Austria. In 2011 BIA Separations entered a strategic partnership with Japan Synthetic Rubber Corporation, a Japanese company producing synthetic materials. A strategic partnership agreement with Showa Denko K.K. (SDK) was signed in 2012.
The only drug currently approved for stroke treatment is tPA, which can cause dangerous brain bleeding. In 2005, Griffin et al proposed using Activated Protein C in conjunction with tPA to protect the brain from tPA’s harmful side-effects. APC activates protease-activated receptor 1 (PAR-1), which plays a role in the interaction of coagulation and inflammation. The 3K3A-APC was designed to have more activity at protease-activated receptor 1 (PAR-1) and less anticoagulative effect than activated protein C. The phase 2 trial, RHAPSODY, was performed in the lab of Berislav Zlokovic, the scientific founder of ZZ Biotech, to determine safety and tolerability of the drug. A phase 3 $30 million trial, RHAPSODY-2, was planned to determine safety and efficacy for treatment of ischemic stroke. However, on November 16, 2023, the National Institutes of Health (NIH) paused the start of the human trial of 3K3A-APC after an investigation by Science Magazine.
Sources: en.wikipedia.org
14-3-3 proteins are a family of conserved regulatory molecules that are expressed in all eukaryotic cells. 14-3-3 proteins have the ability to bind a multitude of functionally diverse signaling proteins, including kinases, phosphatases, and transmembrane receptors. More than 200 signaling proteins have been reported as 14-3-3 ligands. Elevated amounts of 14-3-3 protein in cerebrospinal fluid are usually a sign of rapid neurodegeneration; a common indicator of Creutzfeldt–Jakob disease.
When multiple copies of a polypeptide encoded by a gene form an aggregate, this protein structure is referred to as a multimer. When a multimer is formed from polypeptides produced by two different mutant alleles of a particular gene, the mixed multimer may exhibit greater functional activity than the unmixed multimers formed by each of the mutants alone. In such a case, the phenomenon is referred to as intragenic complementation. E. coli alkaline phosphatase, a dimer enzyme, exhibits intragenic complementation. By changing the amino acids of the wild-type alkaline phosphatase enzyme produced by Escherichia coli, a mutant alkaline phosphatase is created which not only has a 36-fold increase in enzyme activity, but also retains thermal stability. Typical uses in the lab for alkaline phosphatases include removing phosphate monoesters to prevent self-ligation, which is undesirable during plasmid DNA cloning. Common alkaline phosphatases used in research include:
The ABC domain consists of two domains, the catalytic core domain similar to RecA-like motor ATPases and a smaller, structurally diverse α-helical subdomain that is unique to ABC transporters. The larger domain typically consists of two β-sheets and six α helices, where the catalytic Walker A motif (GXXGXGKS/T where X is any amino acid) or P-loop and Walker B motif (ΦΦΦΦD, of which Φ is a hydrophobic residue) is situated. The helical domain consists of three or four helices and the ABC signature motif, also known as LSGGQ motif, linker peptide or C motif. The ABC domain also has a glutamine residue residing in a flexible loop called Q loop, lid or γ-phosphate switch, that connects the TMD and ABC. The Q loop is presumed to be involved in the interaction of the NBD and TMD, particularly in the coupling of nucleotide hydrolysis to the conformational changes of the TMD during substrate translocation. The H motif or switch region contains a highly conserved histidine residue that is also important in the interaction of the ABC domain with ATP. The name ATP-binding cassette is derived from the diagnostic arrangement of the folds or motifs of this class of proteins upon formation of the ATP sandwich and ATP hydrolysis.
The main method of treatment for potential death from signaling-related diseases involves either increasing or decreasing the susceptibility of apoptosis in diseased cells, depending on whether the disease is caused by either the inhibition of or excess apoptosis. For instance, treatments aim to restore apoptosis to treat diseases with deficient cell death and to increase the apoptotic threshold to treat diseases involved with excessive cell death. To stimulate apoptosis, one can increase the number of death receptor ligands (such as TNF or TRAIL), antagonize the anti-apoptotic Bcl-2 pathway, or introduce Smac mimetics to inhibit the inhibitor (IAPs). The addition of agents such as Herceptin, Iressa, or Gleevec works to stop cells from cycling and causes apoptosis activation by blocking growth and survival signaling further upstream. Finally, adding p53-MDM2 complexes displaces p53 and activates the p53 pathway, leading to cell cycle arrest and apoptosis. Many different methods can be used either to stimulate or to inhibit apoptosis in various places along the death signaling pathway. Apoptosis is a multi-step, multi-pathway cell-death programme that is inherent in every cell of the body. In cancer, the apoptosis cell-division ratio is altered. Cancer treatment by chemotherapy and irradiation kills target cells primarily by inducing apoptosis.
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.