If you have been reading about Stationary phase and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2025-09-23. Where a claim depends on a specific study, the study is described rather than over-claimed.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
NSW EPA QLD Health VIC Department of Health SA EPA TAS Department of Health WA Radiological Council NT Department of Health ACT Health and Community Services Directorate Under the ARPANS Act of 1998, the founding of ARPANSA also established the formation of the Radiation Health and Safety Advisory Council, the Radiation Health Committee and the Nuclear Safety Committee. All of these groups consist of the CEO and an individual to represent the interests of the general public, as well as other specialty members. The functions of the Radiation Health and Safety Advisory Council include providing advice to the CEO, identifying emerging issues relating to radiation protection and nuclear safety and examine matters of community concern, among others. The members include: Two radiation control officers An individual nominated by the chief minister of the NT Eight other members The functions of the Radiation Health Committee include developing and reviewing national policies, codes, and standards for radiation protection, and to consult publicly on them, among others. The members include:
Aminoacyl-tRNA synthetase enzymes consume ATP in the attachment tRNA to amino acids, forming aminoacyl-tRNA complexes. Aminoacyl transferase binds AMP-amino acid to tRNA. The coupling reaction proceeds in two steps: aa + ATP ⟶ aa-AMP + PPi aa-AMP + tRNA ⟶ aa-tRNA + AMP The amino acid is coupled to the penultimate nucleotide at the 3′-end of the tRNA (the A in the sequence CCA) via an ester bond (roll over in illustration). Transporting chemicals out of a cell against a gradient is often associated with ATP hydrolysis. Transport is mediated by ATP binding cassette transporters. The human genome encodes 48 ABC transporters, that are used for exporting drugs, lipids, and other compounds.
This can be applied to find the best substrates for proteolytic enzymes. The substrate is displayed on the bacterial cell surface between an affinity ligand and the scaffold, and the kinetics of substrate proteolysis is measured using FACS. Bacterial display can be used to find peptides which bind to specific cells e.g. breast cancer cells or stem cells. Displayed proteins are fluorescently tagged with GFP, so binding interactions between peptides and target cells can be seen by flow cytometry. Control samples are required in order to measure fluorescence levels in the absence of displayed peptides. Samples are also required which don’t contain displayed peptides, but contain mammalian cells and bacterial cells (including the scaffold). Vaccine delivery is a very common application of bacterial surface display. There are two types of live bacterial vaccines that can be made:
Alanine (symbol Ala or A), or α-alanine, is an α-amino acid that is used in the biosynthesis of proteins. It contains an amine group and a carboxylic acid group, both attached to the central carbon atom which also carries a methyl group side chain. Consequently it is classified as a non-polar, aliphatic α-amino acid. Under biological conditions, alanine exists in its zwitterionic form with its amine group protonated (as −NH+3) and its carboxyl group deprotonated (as −CO−2). Alanine is encoded by all codons starting with GC (GCU, GCC, GCA, and GCG). The L-isomer of alanine (left-handed) is the one that is incorporated into proteins. L-alanine is second only to L-leucine in rate of occurrence, accounting for 7.8% of the primary structure in a sample of 1,150 proteins. The right-handed form, D-alanine, occurs in peptides in some bacterial cell walls (in peptidoglycan) and in some peptide antibiotics, and occurs in the tissues of many crustaceans and molluscs as an osmolyte. Alanine is not an essential amino acid in humans because it can be synthesized metabolically and does not need to be present in the diet. However hypoalaninemia (alanine deficiency) is possible under certain conditions such as ketotic hypoglycemia.
CSF drug delivery refers to a number of methods designed to administer therapeutic agents directly into the CSF, bypassing the BBB to achieve higher drug concentrations in the CNS. This technique is particularly beneficial for treating neurological disorders such as brain tumors, infections, and neurodegenerative diseases. Intrathecal injection, where drugs are injected directly into the CSF via the lumbar region, and intracerebroventricular injection, targeting the brain's ventricles, are common approaches. These methods ensure that drugs can reach the CNS more effectively than systemic administration, potentially improving therapeutic outcomes and reducing systemic side effects. Advances in this field are driven by ongoing research into novel delivery systems and drug formulations, enhancing the precision and efficacy of treatments. Intrathecal pseudodelivery refers to a particular drug delivery method where the therapeutic agent is introduced into a reservoir connected to the intrathecal space, rather than being released into the CSF and distributed throughout the CNS. In this approach, the drug interacts with its target within the reservoir, allowing for changing the composition of the CSF without systemic release. This method can be advantageous for maximizing efficacy and minimizing systemic side effects.
Sources: en.wikipedia.org
Animals ingest amino acids in the form of protein. The protein is broken down into its constituent amino acids in the process of digestion. The amino acids are then used to synthesize new proteins and other nitrogenous biomolecules, or they are further catabolized through oxidation to provide a source of energy. The oxidation pathway starts with the removal of the amino group by a transaminase; the amino group is then fed into the urea cycle. The other product of transamidation is a keto acid that enters the citric acid cycle. Glucogenic amino acids can also be converted into glucose, through gluconeogenesis. Of the 20 standard amino acids, nine (His, Ile, Leu, Lys, Met, Phe, Thr, Trp and Val) are called essential amino acids because the human body cannot synthesize them from other compounds at the level needed for normal growth, so they must be obtained from food.
Affimer molecules, also known as adhiron, are small proteins that bind to target proteins with affinity in the nanomolar range. These engineered non-antibody binding proteins are designed to mimic the molecular recognition characteristics of monoclonal antibodies in different applications. These affinity reagents have been optimized to increase their stability, make them tolerant to a range of temperatures and pH, reduce their size, and to increase their expression in E.coli and mammalian cells.
Protein Data Bank (PDB) is a database of three dimensional structures of biological macromolecules, such as proteins and nucleic acids. The data are typically obtained by X-ray crystallography or nuclear magnetic resonance spectroscopy (NMR spectroscopy), and submitted manually by structural biologists worldwide through PDB member organizations – PDBe, RCSB, PDBj and BMRB. The database can be accessed through the webpages of its members, including PDBe (housed at the EMBL-EBI). As a member of the Worldwide Protein Data Bank (wwPDB) consortium, PDBe aids in the joint mission of archiving and maintenance of macromolecular structure data.
Calcitonin gene-related peptide 2 (CGRP2), also called calcitonin related polypeptide beta, is a hormone that in humans is encoded by the CALCB gene (previously CALC2). Like the related hormone, calcitonin gene-related peptide 1 (CGRP1), this hormone induces vasodilation (relaxation of blood vessels) through the activation of the CGRP receptor. This form of calcitonin gene-related peptide is traditionally considered to be the primary form used in the enteric nervous system (nervous system in the gut). The gene that encodes CGRP1, CALCA, also encodes the blood-calcium-reducing hormone calcitonin, but despite its name, this protein is encoded by a distinct gene (CALCB). This hormone activates the CGRP receptor, which is a two protein (heterodimer) complex that is composed of RAMP1 and CALCRL.
Sources: en.wikipedia.org
The psi-loop (Ψ-loop) motif consists of two antiparallel strands with one strand in between that is connected to both by hydrogen bonds. There are four possible strand topologies for single Ψ-loops. This motif is rare as the process resulting in its formation seems unlikely to occur during protein folding. The Ψ-loop was first identified in the aspartic protease family. β-sheets are present in all-β, α+β and α/β domains, and in many peptides or small proteins with poorly defined overall architecture. All-β domains may form β-barrels, β-sandwiches, β-prisms, β-propellers, and β-helices.
The formylglycine tag or aldehyde tag is a convenient 6- or 13-amino acids long tag fused to a protein of interest. The 6-mer tag represents the small core consensus sequence and the 13-mer tag the longer full motif. The experiments on the genetically encoded aldehyde tag by clearly showed the high conversion efficiency with only the core consensus sequence present. Four proteins were produced recombinantly in E.coli with an 86% efficiency of for the full-length motif and >90% efficiency for the 6-mer determined by mass spectrometry. The size of the sequence is analogous to the commonly used 6x His-Tag and has the advantage that it can also be genetically encoded. The sequence is recognized in the ER solely depending on primary sequence and subsequently targeted by FGE. Notably, in the setup of recombinant expression proteins in E. coli a coexpression of exogenous FGE aids full conversion, although E. coli has endogenous FGE-activity. The introduction of an aldehyde tag has a workflow that consists of three segments: A the expression of the fusion protein, that carries the peptide tag derived from the sulfatase motif, B the enzymatic conversion of Cys to f(Gly) and C the bioorthogonal probing with hydrazides or alkoxy amines (Fig. 1).
Years after the conference, people ascribed a large amount of significance to it. According to Paul Berg and Maxine Singer in 1995, the conference marked the beginning of an exceptional era for both science and the public discussion of science policy. The guidelines devised by the conference enabled scientists to conduct experiments with recombinant DNA technology, which by 1995 dominated biological research. This research, in turn, increased knowledge about fundamental life processes, such as the cell cycle. Additionally, the conference, along with public debates on recombinant DNA, increased public interest in biomedical research and molecular genetics. For this reason, by 1995, genetics and its vocabulary had become a part of the daily press and television news. This, in turn, stimulated knowledgeable public discussion about some of the social, political, and environmental issues that emerged from genetic medicine and the use of genetically modified plants in agriculture. Another significant outcome of the conference was the precedent it set about how to respond to changes in scientific knowledge. According to the conference, the proper response to new scientific knowledge was to develop guidelines that governed how to regulate it.
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.