retention time raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
Reviewed 2025-11-24. Anything still debated is marked as such rather than presented as settled.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
| Property | Value | Notes |
|---|---|---|
| Separation principle | Differential partitioning | Analytes distribute between mobile and stationary phases. |
| Mobile phase | Liquid solvent mixture | Composition controls retention and selectivity. |
| Stationary phase | Packed column particles | Often chemically bonded silica. |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is also common. |
| Common synonym | High-performance liquid chromatography | Abbreviated as HPLC. |
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
β-pleated sheet structures are made from extended β-strand polypeptide chains, with strands linked to their neighbours by hydrogen bonds. Due to this extended backbone conformation, β-sheets resist stretching. β-sheets in proteins may carry out low-frequency accordion-like motion as observed by the Raman spectroscopy and analyzed with the quasi-continuum model. A β-helix is formed from repeating structural units consisting of two or three short β-strands linked by short loops. These units "stack" atop one another in a helical fashion so that successive repetitions of the same strand hydrogen-bond with each other in a parallel orientation. See the β-helix article for further information. In lefthanded β-helices, the strands themselves are quite straight and untwisted; the resulting helical surfaces are nearly flat, forming a regular triangular prism shape, as shown for the 1QRE archaeal carbonic anhydrase at right. Other examples are the lipid A synthesis enzyme LpxA and insect antifreeze proteins with a regular array of Thr sidechains on one face that mimic the structure of ice.
Cotadutide is an experimental drug for the treatment of type 2 diabetes mellitus. It lowers blood glucose levels by mimicking the human hormones glucagon-like peptide 1 and glucagon, which play a role in blood sugar regulation. The drug is a peptide that is injected under the skin. Cotadutide is in Phase II clinical trials as of February 2021. Cotadutide, a therapeutic agent, was undergoing Phase II clinical trials. This stage of trials typically involves evaluating the drug's effectiveness and further assessing its safety in a larger group of participants, compared to earlier phases. Glucagon (medication)
The most common peptide aptamer selection system is the yeast two-hybrid system. Peptide aptamers can also be selected from combinatorial peptide libraries constructed by phage display and other surface display technologies such as mRNA display, ribosome display, bacterial display and yeast display. These experimental procedures are also known as biopanning. All the peptides panned from combinatorial peptide libraries have been stored in the MimoDB database.
The advantage in atom economy of using NCAs for peptide formation is that there is no need for a protecting group on the functional group reacted with the amino acid. For example, the Merrifield synthesis depends on the use of Boc and Bzl protecting groups, which need be removed after the reaction. In the case of Bailey peptide synthesis, the free peptide is directly obtained after the reaction. However, unwanted and difficult to remove by-products may be formed. An N-substitution of the NCA (for example, by an o-nitrophenylsulfenyl group) can simplify the subsequent purification process, but on the other hand deteriorates the atom economy of the reaction. The synthesis of NCAs can be carried out by the Leuchs reaction or by the reaction of N-(benzyloxycarbonyl)-amino acids with oxalyl chloride. In the latter case, again the procedure is less efficient in the sense of atom economy. The following peptides were synthesized using this method by 1949:
Sources: en.wikipedia.org
The histology of ALK-negative ALCL, similar to ALK-positive ALCL, consist of "hallmark" cells that strongly express CD30. Unlike ALK-positive ALCL, however, ALK-negative ALC does not fall into different morphological patterns. The histological of this disease may overlap with and be difficult to distinguish from other CD30-positive T-cell lymphomas or the nodular sclerosis form of Hodgkin lymphoma. Cases in which ALK-negative ALCL is not distinguishable from the latter lymphomas are best diagnosed as peripheral T-cell lymphoma not otherwise specified (PTL, NOS). The histology of ALK-negative ALCL may also overlap with tumors of non–T-cell lineage such as various carcinomas. The differential diagnoses of ambiguous cases may be helped by examining the tumor cells for the expression of certain marker proteins. For example, expression of CD56, MUC1 (also termed EMA for epithelial membrane antigen), and clusterin and strong uniform expression of CD30 support the diagnosis of ALK-negative ALCL over PTL, NOS, while variable CD30 expression and extensive expression of T-cell receptor proteins favor PTCL-NOS over ALK-negative ALCL. Detection of certain gene abnormalities (see next section) may also help distinguishing these diseases.
Lab Matters: Each issue of APHL's quarterly magazine, Lab Matters, considers a pressing health issue of importance to public health laboratories. Bridges: Connecting the nation's environmental laboratories, Bridges is APHL's semi-annual newsletter for environmental health professionals. Social Media: APHL is active on Twitter, Facebook and LinkedIn, and has video channels on both YouTube and Vimeo. Blog: APHL's Public Health LabLog features recent and interesting stories about the work of APHL and public health laboratories. 1899: American Public Health Association formed the Committee of Laboratories 1921: Southern Public Health Laboratory Association (SPHLA) formed 1927: SPHLA became State Laboratory Directors Conference and opened membership to other states 1939: SPHLA changed its name to Conference of State and Provincial Laboratory Directors 1951: Association of State and Territorial Public Health Laboratory Directors founded 1998: Renamed the Association of Public Health Laboratories (APHL) and became a more inclusive organization with new membership categories
Projected to go undrafted by Sports Illustrated, who criticized his lack of "balance, body control and ability in space," Kuper was ranked as the No. 28 offensive guard available in the 2006 NFL draft. Kuper was eventually selected in the fifth round, 161st overall, by the Denver Broncos. He was the highest selected North Dakota lineman since Todd Thomas in 1981. Kuper started 79-of-90 games played (68 at right guard) while playing his entire eight-year NFL career with the Broncos. On June 4, 2010, the Broncos announced that they had signed Kuper to a five-year deal worth $25.5 million. The new contract made him the second-highest-paid offensive lineman in Broncos' history, second only to former left tackle Matt Lepsis. In 2010, the Denver Broncos announced that Kuper had been selected as co-captain of the Broncos offense, along with Kyle Orton and Daniel Graham. During the regular season finale in 2011 against the Kansas City Chiefs, Kuper suffered a gruesome broken ankle that ended his season. That season Kuper made the Pro Bowl, but withdrew due to the injury and needed surgery. A three-time captain, Kuper was recipient of the Ed Block Courage Award in 2012 as voted on by his teammates. Kuper retired on March 11, 2014.
Alfred Ellis Wilhelmi (1910–1994) was an American endocrinologist recognized for contributing to the understanding of anterior pituitary hormones. Born in Lakewood, Ohio, Wilhelmi attended Cleveland public schools. Wilhelmi earned a B.S. degree in premedical sciences from Western Reserve University in 1933. He then attended Oxford University as a Rhodes Scholar, where he obtained a B.A. in 1933 and Ph.D. in animal physiology in 1937. He then joined Yale University's Biochemistry Department, rising to the position of Professor in 1950. Wilhelmi chaired the Department of Biochemistry at Emory University School of Medicine from 1950 to 1977. In 1960, he was named Charles Howard Candler Professor of Biochemistry. In 1979, he received Emory's Thomas Jefferson award for service to the university and community. Wilhelmi also was President of the Endocrine Society from 1968 to 1969. During his career, he published over 80 articles in scientific journals.
Non-specific active immunotherapy: generating a general immune system response using cytokines and other cell signaling molecules. Specific active immunotherapy: the generation of cell-mediated and antibody immune responses focused on specific antigens expressed by the cancer cells, typically using a vaccine platform. Active immunotherapies fall under the category of activation immunotherapies, which is a subset of immunotherapies that activate the immune system as opposed immunotherapies that suppress the immune system. Non-specific active immunotherapy is administered with the overall goal of generally eliminating malignant pathogens or cells from the host system. This treatment stimulates the immune system in a general sense, rather than specifically targeting a cell type e.g. cancer cells. Non-specific approaches aim to create a robust immune response that would lead to the eventual killing of malignant cells through immunomodulators such as cytokines.
Sources: en.wikipedia.org
Biochemical differences between different organisms and humans are useful for drug development. For instance, penicillin kills bacteria by inhibiting the bacterial enzyme DD-transpeptidase, destroying the development of the bacterial cell wall and inducing cell death. Thus, the study of binding sites is relevant to many fields of research, including cancer mechanisms, drug formulation, and physiological regulation. The formulation of an inhibitor to mute a protein's function is a common form of pharmaceutical therapy.
Founded in 1984, Bio-Synthesis, Inc. was known as OCS Laboratories and was one of the first companies providing commercially available synthetic oligonucleotides to the biomedical research community worldwide. It was the first producer of commercially available synthetic DNA and became a producer of synthetic peptides in 1985, and became the only company to provide both synthetic DNA and peptide under one roof. Also in 1985 the process, now known as PCR, was discovered by Mullis et al. A key activity for Bio-Synthesis was to synthesize large number of PCR primer thus assisting and solidifying the early adoption of this now common and crucial process in biology.
The major cell-matrix adhesion receptors are integrins and therefore the adhesome of cell-matrix adhesion is referred to as the integrin adhesome. Cell-cell adhesion is primarily mediated by cadherin receptors and therefore the adhesome of cell-cell adhesion is referred to as the cadherin adhesome or cadhesome. The first attempts to establish the set of proteins that participate directly ('bona fide' adhesome components) or affect indirectly ('associated' adhesome components) cell adhesion were based on mining of the primary research literature, and resulted in approximately 200 protein in either integrin or cadherin adhesomes. Later, unbiased proteomic approaches utilizing mass spectrometry have detected hundreds more proteins associated with integrin adhesions. However, a comparison of multiple proteomic studies of the integrin adhesome of fibroblasts attached to fibronectin found only 60 proteins common to all studies. Humphries and co-workers named these 60 proteins the 'consensus integrin adhesome'.
Possibly the most common use of affinity chromatography is for the purification of recombinant proteins. Proteins with a known affinity are protein tagged in order to aid their purification. The protein may have been genetically modified so as to allow it to be selected for affinity binding; this is known as a fusion protein. Protein tags include hexahistidine (His), glutathione-S-transferase (GST), maltose binding protein (MBP), and the Colicin E7 variant CL7 tag. Histidine tags have an affinity for nickel, cobalt, zinc, copper and iron ions which have been immobilized by forming coordinate covalent bonds with a chelator incorporated in the stationary phase. For elution, an excess amount of a compound able to act as a metal ion ligand, such as imidazole, is used. GST has an affinity for glutathione which is commercially available immobilized as glutathione agarose. During elution, excess glutathione is used to displace the tagged protein. CL7 has an affinity and specificity for Immunity Protein 7 (Im7) which is commercially available immobilized as Im7 agarose resin. For elution, an active and site-specific protease is applied to the Im7 resin to release the tag-free protein.
Sources: en.wikipedia.org
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.
Pressure drives the liquid mobile phase through a column packed with small particles. Without pressure, flow would be very slow or stop because the packed bed resists liquid movement. Modern pumps maintain a steady flow despite the resistance.
A chromatogram is a plot of detector signal against time after sample injection. Each peak represents a compound or group of compounds eluting from the column. Retention time and peak area are the main measurements read from the plot.
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.